The fan blades and covers of Yiquanfeng high-pressure blowers are made of the hardest material in the world, which is equivalent to the same material as Mercedes-Benz wheel rims. 2. The bearings of the full-wind blower adopt high-speed and high-temperature-resistant imported bearings, which can rotate / minute at 1000 rpm, and require no lubrication and maintenance. It supports hour-long long-term operation and its performance is stable and reliable.
The inlet and outlet of the Sanquan air blower are equipped with built-in silencer pipes to achieve low noise.
The lower model of the four full air blowers can be used at full pressure.
The pressure of the Wuquanfeng blower is stable. It has been proved by the application of water treatment and electroplating treatment that the mixing is uniform and the water wave tumbling height is consistent.
Under the same power and pressure, the flow rate of six full-wind blowers is greater than that of similar products. The wind cover of Qiquanfeng high-pressure blower adopts a sheet-shaped heat dissipation design, which is equivalent to the heat dissipation device of a motorcycle engine, greatly reducing the temperature of the fan during operation.
Baquanfeng high-pressure annular fan adopts the bearing front design principle. Two bearings are placed at the front end of the fan blade and the rear end of the motor to achieve the best dynamic balance configuration and facilitate heat dissipation. (The reason is that there are heat sinks at the front end of the fan blades for heat dissipation, and the bearings at the rear end work under the fan's own cooling fan, thereby keeping the bearings working at low temperatures for a long time.)
Jiuquanfeng ring fan adopts special anti-vibration feet Designed to greatly reduce vibrations generated during fan operation.
Shiquanfeng high-pressure blower is economical and energy-saving. Under the same power, same pressure and same flow rate, the current of the full-wind high-pressure blower is less than that of other similar products.
Quanfeng’s new generation of high-pressure blowers are on the market, and regional agents across the country are actively being recruited. Agents are welcome to come for consultation and negotiation.
Performance characteristics of full-wind high-pressure blower
Easy to install
Full-wind high-pressure blower can be installed at any time in the place of use to supply compressed air or for evacuation. And can be installed in any horizontal or vertical direction.
Sturdy structure
The body of the full-wind high-pressure blower is made of aluminum alloy, which is different from ordinary blowers made of iron shell or aluminum alloy. The material is the same as the wheel drum of Mercedes-Benz cars, making it stronger and more durable.
High reliability
Except for the impeller, the full-wind high-pressure blower has no other moving parts, and the impeller is directly connected to the motor without gears or transmission belts, so it is highly reliable and almost maintenance-free.
No oil and gas, no pollution. When the impeller rotates, it does not come into contact with anything and requires no lubrication, so it can be guaranteed to be 100% oil-free.
Low Vibration
The parts of the full-wind high-pressure blower are processed and tested with equipment imported from Germany and Japan. The parts in the running part have been designed with extremely precise balance and are tested and calibrated, so the vibration rate is very low.
Low Noise
The full-wind high-pressure blower is directly driven by a high-voltage and low-noise motor. There are built-in mufflers at the entrance and exit, which can reduce the noise during operation.
The model of the full-wind annular blower is as follows. The voltage is single-phase ( ( The voltage is three-phase/ ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( )) The model of the full-wind medium-pressure centrifugal blower is as follows/) ( ( ( ( The model of the through-type blower is as follows. ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( )) The model of Turpu multi-stage blower is as follows. The model of straight-blade blower is as follows. The model of full-wind medium-pressure centrifugal blower is as follows. The model of straight-blade blower is as follows. The cooling fan model is as follows
Supply of full-wind blower NMRV040-7.5-250w through-flow blower